A Pretty Good Retrofit in Montana

first_imgMore recently, I worked as a trainer for the Montana Weatherization Training Center, where I taught classes in weatherization, insulation systems, auditing, zonal pressure diagnostics, and furnace diagnostics and repair. (I got a good education there, too.)In 1994, Laurel and I moved from our original home in Livingston, Montana, to Seattle, where we spent 12 years going to grad school and working. After adopting twin girls from Russia, we decided to move back home to Livingston to raise them and regain some sense of normalcy, as only small town life can provide.On a visit to my mother with the girls, we broached the subject of buying a house for the first time. A realtor friend told us that the market was very tight, but that given a year of looking, she could find us a home. At that point, my mom mentioned that a friend of hers was about to sell her house due to issues with aging. I called her up, got an invitation to visit, and immediately drove across town.Laurel and I walked through the house with quite different reactions. She saw the shag carpeting, green-striped wallpaper, Z-brick, dropped ceilings, and heavy draperies. It was a house that hadn’t been touched in 30 years. I saw an older house with good bones: an adequate roof, a brick exterior, a newish furnace, a 3-wire breaker box, and a solid foundation. The whole process from idea to tour to decision took me about an hour.Several months later, I received the loan documents in the mail, surprising Laurel when I asked for her signature. She swears that she knew nothing about buying a house; I’m sure that we talked about it. As I said, she’s very supportive.Not much insulationWe rented the house out to a family for a year, then moved back home. We’ve been working on the house ever since. Out went the drapes. Out went the shag rugs and wallpaper. And out came the paint brushes. Very supportive.Should I mention that our new house had 4 to 6 inches of Silva-Wool insulation in the attic and in some of the upstairs walls? Other than that, nada — no insulation whatsoever. The windows were a mix of single-hung vinyl replacements and leaky aluminum storm windows over old wood double-hungs. The main floor walls are double-wythe brick with a 2½-inch air gap. Being generous, that’s about an R-6.Livingston averages 7,600 heating degree days. It’s in Climate Zone 6 and is dry, fairly cold, and very windy. The average annual wind speed is 14 mph, though the winter averages are 18 to 20 mph. Unfortunately, it is windy in the winter and calmer in the summer. The initial blower door reading from the utility audit was 2,732 cfm50. It was a cold house that first winter.I should also mention that my wife and I are pretty old school. We keep the heat down and always lower the thermostat 10 degrees at night and when away. We religiously turn the lights off when they aren’t in use. We wash our hands and the laundry with cold water, wash clothes and dishes with full loads, and we heat the upstairs hardly at all. Over these last eight years, I’ve systematically worked my way through the house, from the attic to the basement. My goal is to upgrade the house without affecting the historic appearance of the house. I’ve gone slowly, thinking about each step for years. I’ve also tracked my utility bills religiously. It is my most intensive case study.Good bonesThe form of the house is simple and compact, with a 12:12 roof, not unlike what we are now seeing being designed for Passivhaus buildings around the country. The unheated front porch under the upstairs bedroom and the back porch provide transition spaces to the outdoors. Unlike many houses of the era (1914), the rooms sizes are generous, with high ceilings, wide openings, and large windows. It is really delightful to live in: a good family home.As I said, the house has good bones. There are only a couple of places where the brick arches over the windows have cracked. Otherwise, the brickwork and the 18-inch-thick rubble stone walls in the full-height basement are as solid as when they were built (see Image #2, below).The main floor walls were brick inside and out, with plastered interiors. The second-floor framing is rough-sawn fir with shiplap sheathing. The upstairs is a classic story-and-a-half with balloon framing and two shed dormers. The exterior walls in the kneewall attics were sheathed in cardboard at some point, and most of the second-floor walls were insulated with Silva-Wool, a brand name for a precursor of cellulose insulation (see Image #3, below).One of the benefits of an uninsulated, leaky structure is that there were no signs of moisture in the house other than some efflorescence on the basement walls and on the brick chimney in the attic. This house is as strong as when it was built. With care, it should last another hundred years. I just love the rough-sawn fir framing, the old trim, and the brick walls.The auditors gave us a “to do” listSoon after moving in, I started on my upgrade program. First, I applied for a utility audit.The auditors did a blower door test, installed a few upgrades, and made a series of recommendations for additional insulation. To date, we’ve done everything on their list, and more.Efficient lights and appliancesSome of my decisions have been easy. I’ve replaced almost all of the lights with CFLs the first year and more recently installed some LEDs.We bought a front-loading washer and dryer set and hung up a multi-line retractable clothesline outside. As time went on, and the old appliances started to fail, the other appliances have been replaced with better Energy Star products. The dryer, which is electric, doesn’t get used much, except in the coldest time of the year. The kitchen range is a standard electric-resistance glass top.Insulating all five atticsMy first major project was to rework the attic. It is in five sections because of the story-and-a-half structure and the two shed dormers.I wanted to connect the four kneewall attics with the upper main attic to provide ventilation, so I installed cardboard vent chutes at the outside eaves, and up the sloped sections between the lower and upper attics (see Image #4, below). The kneewalls were sheathed with cardboard and had been blown with Silva-Wool. I added 2 inches of foil-faced polyisocyanurate to the kneewalls, taping the joints and foaming the edges (see Image #5).I also built a stout plywood attic hatch.After installing and wiring in smoke detectors, some extra outlets, and a new bathroom exhaust fan (see Image #6), I sealed up all the wire penetrations, junction boxes, and gaps around the vent stacks (see Images #7 and #8). I didn’t systematically seal up the cracks at the top plates of partitions (because the existing insulation was in the way) and now I wonder about that decision. I also didn’t install blocking to seal up the joist cavities below the kneewalls before blowing in insulation on the flats.After all this prep work, the insulators blew R-60 of cellulose over the existing Silva-Wool insulation (see Image #9).After blowing insulation in the attic, the pressure difference between the house and the attic zones was measured at 46 Pascals when running the blower door.Blower door results keep getting betterI came back with the infrared camera and blower door a couple of times after the attic was insulated. I found a couple of dozen wall cavities and sloped ceiling cavities that weren’t insulated. These cavities were then blown with dense-packed cellulose (see Images #10 and #11).Prior to refinishing the fir floors upstairs, I also pulled up the quarter-round molding and caulked the joint between the flooring and baseboard.An old gas fireplace upstairs was connected directly to a kneewall attic, so the fireplace had to be dismantled and the area sealed. Beyond that, I’ve installed new door thresholds and weather-stripping and sealed plumbing penetrations in the basement ceiling.A recent blower door reading, prior to insulating the basement, was around 1,850 cfm50. After spraying the basement walls, the reading dropped to 998 cfm50. Eliminating the open combustion furnace helped too.Four new vinyl windowsThe windows in the house were a mix of original wooden double-hungs with aluminum storms and single-hung vinyl replacements, none of which were very airtight.Our upstairs is particularly exposed to winter winds, so I replaced four of those wooden windows with new vinyl casements that had triple weatherstripping and multi-point locking hardware. The new windows had a U-factor of 0.29, the lowest U-factor I could find locally.Blown-in fiberglass fills the gap in the brick wallsAfter taking a couple of years to recuperate and think, I committed to insulating the double-wythe brick walls on the main floor. I puzzled for years over what type of insulation would work, in terms of access, R-value, moisture issues, and ease of installation.In the end, having become familiar with dense-packing techniques used by weatherization workers, I elected to use short-fiber fiberglass. I realized that I could access all areas of the walls by drilling through the window and door jambs (see Images #12 and #13).It was a fairly tough prep job, but went smoothly once the insulation process started. We used high air pressure and we closed down the insulation gate to maximize throw and density. I was able to verify the throw of insulation fibers by checking the holes in adjacent window jambs while blowing the intervening walls. I’m confident that we were able to fill all the cavities except for the built-up header area over the windows. Interestingly, the infrared camera wasn’t useful on these high-mass walls. The bag count of insulation was on target.My calculation was that we increased the R-value of the walls from R-5 or R-6 to R-12 or R-14. That’s not good enough, but is all that was possible unless we went with an exterior cladding system.The most immediate change we noticed was that the house was markedly quieter, which was interesting, given the quietness of masonry houses.Closed-cell spray foam for the basement wallsThe basement walls are 18-inch-thick rubble stone walls with absolutely no cracking or signs of settling. There is some efflorescence on the lower walls in a couple of places which will be dealt with by regrading the exterior and improving the rain gutters.In the basement, the floor joists sit on a 2×4 mudsill. There isn’t a rim joist, but rather two wythes of brick on the exterior side of the floor framing.I’ve became convinced that there is some air infiltration through the brick rim and the stone foundation. The interior of the rim joist area and the basement walls was skinned with high-density spray foam: 3 inches of foam at the top, tapering down to 1 inch at the floor (see Image #14). In the near future, the interior walls will be framed with studs and then I’ll install unfaced fiberglass batts and drywall.A new furnaceJudging from the age of the house and a blocked-off coal chute, the original furnace in the house was probably an octopus-type cast-iron coal furnace that used large ducts in a gravity feed arrangement. At some point, the original furnace had been replaced with a 1988 Lennox Type I furnace rated at 120,000 BTU/h.The plenums were connected to the original registers with flex duct. The original floor boots were insulated with asbestos, so I donned my Tyvek suit and respirator, soaked the asbestos, and peeled off what I could. Then I painted on a coating of duct mastic over the remaining asbestos. I also sealed the boots to the adjacent subfloor with foam and caulk.The Lennox furnace had a motorized damper on the combustion air and tested at 82% efficient. Normally I wouldn’t consider replacing it with a more efficient furnace because the payback just isn’t there. The older furnace, however, only ran about half the time at -20°F. Additionally, the supply air to the house was too cool and the flue pipe into the brick chimney was rusted. I began to suspect that the fan on the furnace was oversized and cooling off the heat exchanger too much.A year ago I ran across a great deal on a 95% efficient gas furnace and couldn’t resist the challenge of my first furnace installation. The new furnace was rated at 80,000 BTU/h input rather than 120,000 BTU/h, a more appropriate size for the now insulated house. Because this was my first experience at furnace installation, I carefully read the manual and then laid out, starting with the biggest elements, the furnace location, sheet metal plenums, branch ducts, plastic flues, gas line, and electrical hook-up.After setting the furnace in place, I had a local sheet-metal shop build new plenums and a new trunk line. After these were installed, I connected the rest of the ductwork which included some new metal take-offs, dampers, and fittings. The existing flex duct was then attached and sealed (see Image #15). I had a licensed plumber install the gas line and I tied in a new circuit from the breaker box.The furnace has run flawlessly since the initial start-up. It is noisier than the old furnace, but the supply air is much warmer. I was surprised that the new furnace still only ran about 50% of the time when outside temperature was -20°F. I should have considered an even smaller furnace.I also had discovered that my water heater (an atmospherically vented gas-fired model) failed the worst-case depressurization test — it backdrafted. The water heater had a 3-inch metal flue that had been vented into a 6″x8″ unlined brick chimney, and I expected that its draft would be even worse once it was “orphaned.” Installing a sealed-combustion furnace should eliminate some of the competition for combustion air in the basement, but the water heater would have trouble establishing draft by itself in the cold unlined brick chimney. To improve the draft, I installed a 4-inch flue liner.Improved comfortAfter each one of these chapters, Laurel and I have felt a noticeable improvement in comfort, both summer and winter. The house is much quieter too.We’ve been able to eliminate all four of the upstairs ceiling fans and the use of a window air conditioner in the summer. Livingston usually gets a week or so of hot weather in the summer when the outdoor temperatures are in the high 90s or lower triple digits. Usually nighttime temperatures fall by 20 to 30 degrees. By conscientiously opening and closing curtains and windows, the house stays delightfully cool all summer.We sometimes do get a night or three when it doesn’t cool off at night and we have to sleep with just a sheet. This summer, we had a week of mid 90s weather, reaching a peak of 105ËšF. The highest indoor temperature was 76ËšF. With better airflow through the house, I think that we could do even better.In the winter, we’ve found that the house feels warmer after all these improvements. We are still running the setbacks on the new programmable thermostat, about the same as we did with the old Honeywell, and leave the heat off upstairs, so I think that we haven’t changed our behavior or expectations with all the changes. I do hear less grumbling from the girls about the cold, and they use the upstairs bedrooms more during the day. Laurel and I do leave a bedroom window cracked all winter, so that probably affects the house performance a bit.Quantifying the savingsMagazine articles describing new innovative green homes have always driven me crazy. Pretty pictures, construction drama, cool equipment, and bragging rights. Very rarely are energy predictions correlated to actual energy usage. Rarely is energy savings quantified in any way.I’ve been pretty anal about record-keeping, collecting utility bill data in a spreadsheet every month since we bought the house in 2005. I track electricity and gas consumption (see Image #18) and energy costs, average outdoor temperature, and Heating Degree Days. From all of this, I calculate ratios and make graphs. I’ve also kept track of my construction expenses (see Image #17) and calculated my cash flow (see Image #19).In eight years, we’ve reduced space heating requirements by 60%, electric use by 45%, and air leakage by 63%. This past winter, I installed a PV system that is slightly oversized, so now I only pay the monthly service charge. With that addition, utility bills have been reduced from $1,960 in 2005/2006 to about $600 in 2015/2016.Factoring in some energy inflation, I project that I will save around $31,000 in 20 years on an investment of $5,520 just for the space heating improvements.A good return on our investmentMy approach to energy conservation on my own house has been conservative. I’m pretty hard-core about saving energy, but very cautious about spending money if there isn’t a return on my investment. I’ve done very well financially on this project with this approach. It did help that we started with a house that was almost totally uninsulated, so the percentage of energy savings was significant. We also haven’t gone overboard by replacing windows or cladding the exterior walls. The best part is that we live in a great old house which is comfortable and affordable.So what to do now? The kids are grown. The house is finished and much too big for the two of us. I guess it’s time for a mid-life crisis. Maybe I’ll start looking around. I’ve always had a roving eye. Those mid-century moderns look pretty sweet. HOUSE AT A GLANCELocation: Livingston, MontanaSize: 2,200 square feetDate of Construction: 1914Bedrooms: 4 or 5Bathrooms: 2Foundation: Full basement; 18″ rubble stone walls, concrete floorFirst floor walls: 2 wythes brick with 2½” air gapSecond floor walls: Rough-sawn 2x4s with shiplap sheathingSecond floor siding: Cedar shinglesRoof framing: 2×6 rafters and ceiling joistsExisting windows: About half were original wood single-glazed double-hung windows with aluminum storms; half are replacement vinyl single-hungs with U-0.5 glass.Existing doors: Wood panel doors.Space heat: 120,000 Btu/h natural gas furnace was replaced with 80,000 Btu/h 95% condensing furnaceDomestic hot water: Gas water heater (atmospherically vented)Kitchen range: ElectricClothes dryer: Electric RELATED ARTICLESOne Man’s Quest for Energy IndependenceA Leaky Old House Becomes a Net-Zero ShowcaseMission Zero House: A Net-Zero RetrofitRetrofits versus ReductionsDeep Energy Retrofits Are Often MisguidedThe History of the Chainsaw RetrofitThe High Cost of Deep-Energy RetrofitsEnergy-Efficiency Retrofits: Insulation or Solar Power? Brand New Appearance and Performance for An Older DuplexDeep Energy Makeover: One Step At A TimeAn Old House Gets a Superinsulation RetrofitRoofing and Siding Jobs Are Energy-Retrofit OpportunitiesFrom ‘Tea House’ to Tight House This is a story of a wonderful, tempestuous relationship. For me, it began nine years ago as an unplanned series of events: a chance encounter between a wandering idealist and small town girl. The happenstance meeting quickly progressed to an impulsive, long-term proposal. Soon thereafter, the commitment was formalized by the exchange of legal documents through the mail.Like most marriages, this hasty decision resulted in an ongoing set of improvisations over the way we dance through life together. I was the driven agent of change; she, the stubborn, old-fashioned, and wise woman who continually forced me to prove up. These nine years have been tough but rewarding, and I’m a better man for it.I’m talking about my house, of course. My real marriage has been rewarding in other ways. My wife Laurel has been patient, supportive, and engaged. (It really helps that she worked as a house painter and wallpaper hanger for 15 years.)Should we buy a house?I’m a builder and designer whose study of energy efficiency has been a life-long passion. I got my start in the mid 1970s, and have built a number of passive solar and superinsulated houses. I’ve also worked on historic houses and other projects in southwest Montana. Later, I earned a M.Arch. degree from the University of Washington and then worked for a couple of architectural firms.last_img

Leave a Reply

Your email address will not be published. Required fields are marked *